Aluminium Alloy
Commercial Alloy
5754 - H111 Treadplate
Aluminium alloy 5754 has excellent corrosion resistance especially to seawater and industrially polluted atmospheres.
It has higher strength than 5251. This high strength makes 5754 highly suited to flooring applications.
Applications
5754 is typically used in:
~ Treadplate
~ Shipbuilding
~ Vehicle bodies
~ Rivets
~ Fishing industry equipment
~ Food processing
~ Welded chemical and nuclear structures
Please note that Mechanical Properties shown are for H111 temper.
Chemical Composition
|
BS EN 573-3:2009 Alloy 5754 |
|
|---|---|
| Chemical Element | % Present |
| Manganese (Mn) | 0.0 - 0.50 |
| Iron (Fe) | 0.0 - 0.40 |
| Magnesium (Mg) | 2.60 - 3.60 |
| Silicon (Si) | 0.0 - 0.40 |
| Chromium (Cr) | 0.0 - 0.30 |
| Copper (Cu) | 0.0 - 0.10 |
| Manganese + Chromium (Mn+Cr) | 0.10 - 0.60 |
| Other (Each) | 0.0 - 0.05 |
| Others (Total) | 0.0 - 0.15 |
| Titanium (Ti) | 0.0 - 0.15 |
| Zinc (Zn) | 0.0 - 0.20 |
| Aluminium (Al) | Balance |
Alloy Designations
Alloy 5754 also corresponds to the following standard designations and specifications but may not be a direct equivalent:
A95754
Al Mg3
Al 3.1Mg Mn Cr
AW-5754
Generic Physical Properties
| Physical Property | Value |
|---|---|
| Density | 2.66 g/cm³ |
| Melting Point | 600 °C |
| Thermal Expansion | 24 x10^-6 /K |
| Modulus of Elasticity | 68 GPa |
| Thermal Conductivity | 147 W/m.K |
| Electrical Resistivity | 0.049 x10^-6 Ω .m |
Mechanical Properties
|
BS EN 485-2:2008 Sheet - 0.2mm to 6.00mm |
|
|---|---|
| Mechanical Property | Value |
| Proof Stress | 60 Min MPa |
| Tensile Strength | 160 - 200 MPa |
| Hardness Brinell | 44 HB |
| Elongation A50 mm | 12 Min % |
Weldability
Weldability – Gas: Excellent
Weldability – Arc: Excellent
Weldability – Resistance: Excellent
Brazability: Poor
Fabrication
Workability – Cold: Very good
Machinability: Average
Disclaimer
This Data is indicative only and as such is not to be relied upon in place of the full specification. In particular, mechanical property requirements vary widely with temper, product and product dimensions. All information is based on our present knowledge and is given in good faith. No liability will be accepted by the Company in respect of any action taken by any third party in reliance thereon.
Please note that the 'Datasheet Update' date shown above is no guarantee of accuracy or whether the datasheet is up to date.
The information provided in this datasheet has been drawn from various recognised sources, including EN Standards, recognised industry references (printed & online) and manufacturers’ data. No guarantee is given that the information is from the latest issue of those sources or about the accuracy of those sources.
Material supplied by the Company may vary significantly from this data, but will conform to all relevant and applicable standards.
As the products detailed may be used for a wide variety of purposes and as the Company has no control over their use; the Company specifically excludes all conditions or warranties expressed or implied by statute or otherwise as to dimensions, properties and/or fitness for any particular purpose, whether expressed or implied.
Advice given by the Company to any third party is given for that party’s assistance only and without liability on the part of the Company. All transactions are subject to the Company’s current Conditions of Sale. The extent of the Company’s liabilities to any customer is clearly set out in those Conditions; a copy of which is available on request.
