+44 (0)1487 833 600
Wilsons is COVID-19 Compliant

Data Sheets

Aluminium Alloy

Commercial Alloy

6060 - T5 Extrusions


Aluminium alloy 6060 is a medium strength heat treatable alloy with a strength slightly lower than 6005A. It has very good corrosion resistance and very good weldability plus good cold formability especially in temper T4. It is commonly used alloy for very complex cross sections and has very good anodizing response.

Applications
Alloy 6060 is typically used for extrusions with complex cross sections and/or requiring anodising:
~ Architectural sections for windows, doors, curtain walls
~ Interior fittings, frame systems, lighting, ladders, railings, fences
~ Heat sink sections, electronic modules, electro motor housings
~ Flexible assembly systems, special machinery elements
~ Truck and trailer flooring, pneumatic installation, railway, inside applications
~ Irrigation, heating and cooling pipes
~ Furniture, office equipment.

Chemical Composition

BS EN 573-3:2009
Alloy 6060
Chemical Element % Present
Manganese (Mn) 0.0 - 0.10
Iron (Fe) 0.10 - 0.30
Magnesium (Mg) 0.35 - 0.60
Silicon (Si) 0.30 - 0.60
Copper (Cu) 0.0 - 0.10
Zinc (Zn) 0.0 - 0.15
Titanium (Ti) 0.0 - 0.10
Chromium (Cr) 0.0 - 0.05
Other (Each) 0.0 - 0.05
Others (Total) 0.0 - 0.15
Aluminium (Al) Balance

Generic Physical Properties

Physical Property Value
Density 2.70 g/cm³
Melting Point 655 °C
Thermal Expansion 23.4 x10^-6 /K
Modulus of Elasticity 69.5 GPa
Thermal Conductivity 209 W/m.K
Electrical Resistivity 54 % IACS
Electrical Resistivity 0.032 x10^-6 Ω .m

Mechanical Properties

BS EN 755-2:2008
Extrusions - Up to 150mm Dia., 15mm WT tube, 5mm WT profiles
Mechanical Property Value
Proof Stress 120 Min MPa
Tensile Strength 160 Min MPa
Elongation A50 mm 6 Min %
Hardness Brinell 60 HB
Elongation A 8 Min %

Weldability

Weldability – Gas: Good

Weldability – Arc: Very Good

Weldability – Resistance: Good

Brazability: Very Good

Solderability: Good

Fabrication

Workability – Cold: Good

Machinability: Acceptable

Anodising: Very Good


Disclaimer

This Data is indicative only and as such is not to be relied upon in place of the full specification. In particular, mechanical property requirements vary widely with temper, product and product dimensions. All information is based on our present knowledge and is given in good faith. No liability will be accepted by the Company in respect of any action taken by any third party in reliance thereon.

Please note that the 'Datasheet Update' date shown above is no guarantee of accuracy or whether the datasheet is up to date.

The information provided in this datasheet has been drawn from various recognised sources, including EN Standards, recognised industry references (printed & online) and manufacturers’ data. No guarantee is given that the information is from the latest issue of those sources or about the accuracy of those sources.

Material supplied by the Company may vary significantly from this data, but will conform to all relevant and applicable standards.

As the products detailed may be used for a wide variety of purposes and as the Company has no control over their use; the Company specifically excludes all conditions or warranties expressed or implied by statute or otherwise as to dimensions, properties and/or fitness for any particular purpose, whether expressed or implied.

Advice given by the Company to any third party is given for that party’s assistance only and without liability on the part of the Company. All transactions are subject to the Company’s current Conditions of Sale. The extent of the Company’s liabilities to any customer is clearly set out in those Conditions; a copy of which is available on request.